The Foundation of Plumbing Knowledge for Bathtub Installation
The Foundation of Plumbing Knowledge for Bathtub Installation
Blog Article
Listed here in the next paragraph you will discover lots of professional points in relation to Tools You Need to Install a New Bathtub .
Mounting a tub isn't specifically rocket science, yet it does need solid plumbing, woodworking, and occasionally, tiling skills. Changing an old bath tub with a brand-new one is also a reasonably tough task. If the old tub is conveniently available, the job can relocate speedily; if you need to open a wall to get rid of the old tub as well as place the brand-new bathtub, the task is a lot harder. In either case, the job is within a residence handyman's skills, although you will certainly require a helper to vacate the old bathtub and also embeded in the new one. Ensure you have actually certified yourself for the work and fit attempting it. As opposed to employing a service provider to take over a halfway-completed job, it is far better to take into consideration utilizing one prior to you start. Possibilities are you might require a specialist plumber to make tube connections.
This short article will certainly help you set up a brand-new tub in your bathroom if you have currently bought a new bathtub as well as don't need to alter the arrangement of your previous water system pipelines.
Your tools and material list ought to comprise the following:
Getting ready for the Installment
Firstly, the supporting framework provided with the bathroom needs to be fitted (if required) according to the producer's directions. Next, fit the faucets or mixer to the bath tub. When fitting the faucet block, it is very important to ensure that if the tap features a plastic washer, it is fitted in between the bath and the faucets. On a plastic bathroom, it is additionally reasonable to fit a supporting plate under the taps device to avoid pressure on the tub.
Fit the flexible faucet ports to the bottom of both faucets using 2 nuts as well as olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet through the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Ensure you make use of all of the supplied washing machines.
Link the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Link the bottom of the overflow tube in a similar manner.The bath must currently be ready to be suited its last placement.
Removing Old Touches
If you require to replace old faucets with brand-new ones as a part of your installation, after that the first thing you ought to do is detach the water. After doing so, activate the faucets to drain pipes any water remaining in the system. The procedure of eliminating the existing faucets can be rather problematic because of the limited gain access to that is frequently the instance.
Utilize a container wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipes to the taps. Have a fabric prepared for the remaining water that will originate from the pipes. As soon as the supply pipelines have actually been removed, utilize the very same device to loosen the nut that holds the faucets onto the bath/basin. You will need to quit the single taps from transforming throughout this process. As soon as the taps have been removed, the holes in the bath/basin will certainly need to be cleaned of any type of old securing compound.
Prior to carrying on to fit the brand-new taps, compare the pipeline connections on the old faucets to the brand-new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the new faucets to fit.
Setting up the Tub
Making use of both wood boards under its feet, position the bath tub in the required position. The wood boards are helpful in evenly spreading the weight of the bathtub over the location of the boards rather than concentrating all the weight onto four little points.
The following goal is to guarantee that the tub is leveled all round. This can be achieved by inspecting the level and also readjusting the feet on the bathtub up until the spirit level checks out degree.
To set up faucets, fit all-time low of the furthest versatile faucet connector to the appropriate supply pipeline by making a compression join; after that do the exact same for the various other tap.
Activate the supply of water and also examine all joints as well as new pipework for leaks and also tighten them if essential. Fill up the bath tub as well as additionally examine the overflow outlet as well as the typical electrical outlet for leakages.
Finally, repair the bathroom paneling as described in the supplier's instruction manual. Tiling and securing around the bath tub needs to wait up until the bathtub has been used at least once as this will settle it into its final setting.
Suitable New Taps
If the tails of the new taps are plastic, after that you will certainly need a plastic port to avoid damage to the thread. One end of the port fits on the plastic tail of the faucet and also the various other end provides a link to the existent supply pipelines.
If you require to fit a monobloc, after that you will certainly need minimizing couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next off, place the tap in the mounting hole in the bath/basin making sure that the washers are in area between the faucet as well as the sink. Secure the faucet in position with the manufacturer offered backnut. As soon as the faucet is safely in place, the supply pipelines can be attached to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with regular tap ports. The previous kind ought to be attached to the tap ends initially, tightening up only by hand. The supply pipes can later be linked to the various other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Tub
In the location where the bathroom fulfills the floor tile, it is required to seal the joins with a silicone rubber caulking. This is necessary as the fitting can relocate enough to crack a rigid seal, triggering the water to pass through the wall surface between the bath as well as the tiling, causing problems with wetness and also possible leaks to the ceiling below.
You can pick from a selection of coloured sealants to assimilate your fixtures as well as fittings. They are sold in tubes as well as cartridges, and are capable of sealing gaps as much as a width of 3mm (1/8 inch). If you have a larger space to fill up, you can fill it with twists of soaked paper or soft rope. Keep in mind to always fill up the tub with water before securing, to allow for the activity experienced when the bathtub is in usage. The sealer can break rather early if you do not think about this motion prior to sealing.
Additionally, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally easily readily available on the market. It is advisable to fit the floor tiles using water-resistant or water-proof adhesive as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Hopefully you enjoyed reading our section on A Step-by-Step Guide to Installing a Bathtub. Thanks a ton for taking a few minutes to read through our piece. Enjoyed our review? Please share it. Help others locate it. I treasure reading our article about How to Install a Bathtub.
Book Report this page